Dekro Super Fibretex

R489.72R2,074.78 inc. VAT

Acrylic co-polymer emulsion.

DOWNLOAD DATA SHEET

SELECT PRODUCT OPTIONS
Dekro Rippletex
Dekro Hydrosilk

Need more info about this product?

Send us an enquiry and we will get back to as soon as possible.

By enquiring you agree to our Privacy Policy and we’re offering you chance to join our newsletter.

Description

Most textured coats contain sand, silicate, mica or other coarse particles.  These are used to assist in the textured appearance and to bridge cracks.  The disadvantage is that these coatings have a high degree of dirt retention.

  • Super Fibretex is specially formulated with cellulose fibres to give a slight textured appearance and bridge hairline cracks without being too rough.  This results in a coating that has low dirt retention, giving a much longer coating life.
  • Super Fibretex should be used where outstanding durability and waterproofing properties are required.

Additional information

Weight N/A
COLOUR

Clay Brown, Concrete Grey, Honey Yellow, Moss Grey, Ochre Yellow, White, Yellow Grey

SIZE

5L, 20L

Cement Surfaces

Remove dust, dirt and plaster splashes. Open large cracks and imperfections. Fill with an appropriate Crack Filler and sand smooth when dry.
Apply one coat of Dekro Masonry Primer.
Apply one or two coats of Super Fibretex – depending on quality of finish required
Allow at least 4 hours drying time between coats

Metal Surfaces – Iron,  Cast Iron;  Galvanised Iron. 

Loose surface rust must be removed by wire brushing. Remove all grease and oil with detergent solution or Mineral

Old metal 

Apply one coat of Hydrobond 44 and allow to dry for one hour before applying a second coat of Hydrobond 44. Allow to dry for minimum of 8 hours before overcoating. Apply two coats of Super Fibretex, allowing at least 4 hours drying time between coats.

New metal 

New galvanised iron surfaces must be cleaned to a water break-free surface with Galvanised Iron Pre-cleaner, then rinsed with water.
Prime Galvanised Iron with Vasbyt Etch Primer.
Prime Mild Steel with Ultra Q.D. Zinc Phosphate Primer.

Woodwork 

Clean to remove dirt, grease and dust.
Sandpaper to a smooth surface and dust off.
Apply one coat of Dekro Pink Wood Primer (for exterior) or Dekro Universal Undercoat (for interior).
Allow to dry.
Apply two coats of Super Fibretex, allowing at least 4 hours drying time between coats.

Previously painted surfaces, redecoration;  PVA;  Acrylic Emulsion;  Gloss;  Eggshell Paint in Good Condition

Wash down with water or detergent to remove all dirt, grease and other contaminants.
Cut out large cracks and imperfections, fill with an appropriate crack filler and sand smooth when dry.
Sand gloss paint surfaces to a matt finish, then rinse with water and allow to dry, (alternatively Universal Undercoat can be used).
Apply one or two coats of Super Fibretex – depending on condition of surface and quality of finish required.
Allow at least 4 hours drying time between coats.

PVA;  Acrylic Emulsion; Gloss, Eggshell Paint in Poor Condition. 

Remove completely by scraping, wire brushing, hydro-blasting, burning or paint remover to bare sound surface.
Stop and fill all large cracks and imperfections with an appropriate crack filler. Allow to dry and sand smooth when dry.
Apply one coat of Dekrolite Masonry Paint. Allow to dry.
Apply two coats of Super Fibretex, allowing at least 4 hours drying time between coats.

GENERAL

Different surfaces and environmental conditions require specific painting systems to produce the best possible results.
It is therefore recommended that you contact a Dekro Sales representative for advice on all your painting requirements, whenever possible.

Type – Acrylic co-polymer emulsion.
Drying Time – Surface : 1-1,5 hours (at 23°C and 50% relative humidity)
Hard dry 3 – 4 hours (at 23°C and 50% relative humidity)
Overcoating – 4 hours.
Viscosity – 93-95 Ku (ROD)
Volume Solids – 41 – 43% (100μ wet film will give dry film).
Gloss – Low Sheen
Spreading Rate – D.F.T. 48 – 52 μ at ± 6 m² / litre
Coverage (Theoretical) – 4 – 5 m² to obtain full coverage.
Flash Point – Not applicable.
Colour Range – White, range of standard colours as per current colour card.
Packing Size – 5 litre, 20 litre.

All above technical data is based on Super Fibretex White only. Coverage/spreading rate of colours depend on condition and porosity of the surface and the manner in which Super Fibretex is applied and used. For best results do not exceed a spreading rate of 6m² per litre.

  • To ensure a consistent appearance ensure that the batch numbers on all Containers are the same.
  • Where batch numbers on containers differ, intermix before use.
  • Do not apply direct to new galvanised iron, sand blasted steel or aluminium.
  • Do not apply directly to untreated knots.
  • Application to areas where temperature exceeds 60°C – is not recommended.
  • For diluting use water only, if required.
  • Do not use Mineral Turpentine, Lacquer Thinner or Meths for diluting as this will alter or destroy the quality and performance of Super Fibretex.
  • Clean all equipment and tools with water after use.

Other products in this category

Brushes, rollers, accessories & supplies

Click here for everything you will need to get the job done!

How-to-guides & expert tips

Click here for how-to-guides, videos & tips for every scenario.

Menu
ONLINE PRODUCT PRICESPLEASE NOTE

All product prices displayed on this website are valid for online purchases only and may differ from prices in store.